The bell housing series EB are designed for coupling hydraulic pumps having ISO flanges to electric motors having metric flanges. These bell housing are precisely machined to reduce misalignment of coupled shafts. The correct alignment of the shafts along with the cushioned power transmission through a resilient spider increases the life of the bearings of the pump/motor coupled. The construction also reduces the noise generation considerably.

Heavy duty construction. Renewable internal parts by replacement. Integral Relief and Release valves. Collapsible hand movement at low pressure.

Hand pump model HP*-D are compact heavy duty pumps designed for industrial applications like operating small presses, fixtures as well as providing source of oil for hydraulically operated emergency equipments. These hand pumps are equipped with integral Rotary Directional Control Valve with two outlet ports for switching of the flow between the two sides of a double acting cylinder. The Rotary valve has pressure holding ability.

Hand pumps series HPTS** are identical in specifications to series HP** pumps, except that, these pumps are meant for mounting on the side wall of oil reservoir / tank of a hydraulic system and therefore can be integrated into the main system as a stand-by pump or can be used as a power source for cylinders or jacks which need large volume of oil for their actuation by mounting them on side wall of suitably designed oil tank.

Automatic change-over from high discharge at low pressure to low discharge at high pressure. Renewable internal parts by replacement. Collapsible Hand lever for compact size and short hand movement.

Automatic change-over from high discharge at low pressure to low discharge at high pressure. Renewable internal parts by replacement. Collapsible Hand lever for compact size and short hand movement.

Direct acting with guided cushioned poppet. Available in Cartridge, Threaded and Subplate types.

Hydraulically cushioned valves, used to control sequencing, relieving, unloading or counter-balancing operations.

Direct acting construction with built-in pressure relief for secondary port.By-pass Check Valve optional.

Direct acting spool type pressure sequence valve. Models available :
Internal pilot, internal drain.
External pilot, internal drain.
Internal pilot, external drain.
External pilot, external drain.
Port A normally connected to port T : control at port P port A normally connected to port T : control at port B Four pressure ratings 25, 50, 100, or 200 bar.For reverse free flow, optional check valve can be supplied as a stackable module. Pressure adjustment by screw or hand knob.

Two stage Spool type Relief / Reducing Valve Cartridge Low pressure override due to larger flow area.
Two options for pressure adjustment,
- With set screw and lock nut.
- With hand knob and lock nut.
Internal drain valves can be converted to external drain.

Two stage Spool type Relief / Reducing Valve Cartridge Low pressure override due to larger flow area.
Two options for pressure adjustment,
- With set screw and lock nut.
- With hand knob and lock nut.

Pilot operated pressure relief valve modular construction for vertical stacking assemblies.
For Cartridge Valve details refer p09605
Interface conforming to ISO 4401 - AB - 03 -04 - A, IS 10187, DIN 24340 Four models available.

Pilot operated pressure reducing valve modular construction for vertical stacking assemblies.
For Cartridge Valve details refer p09605
Interface conforming to ISO 4401 - AB - 03 -04 - A, IS 10187, DIN 24340 Four models available.

Pilot operated seat type valve. High flow handling capacity, low pressure override, remote controllability and solenoid unloading possibility are the main features of these valves. Bodies available with threaded ports or sub-plate mounting style.

Two stage poppet type Relief cum unloading valve. Additional solenoid unloading facility as an optional feature. Three standard sizes - 10, 20, & 30.

Two stage pilot operated construction. These valves are normally open type valves. When the pressure in the secondary port ( port B ) increases to set pressure, the valve closes against the spring.

Designed to control double pumps of a Hi-Low system. Unloads low pressure pump when system pressure rises above the pressure set on unloader valve. Relieves high pressure pump when system pressure reaches the value.

Designed to control Double pumps of a Hi-Low system. Consists of a High pressure relief valve, a Check valve and a low pressure unloading valve. Unloading of pumps by Solenoid valve / Valves as an optional feature.

Designed to control Double pumps of a Hi-Low system. Consists of a High pressure relief valve, a Check valve and a low pressure unloading valve. Unloading of pumps by Solenoid valve / Valves as an optional feature.

Counter balance valves are seat type valves. They offer free-flow from their port B to A and give leak free closure in opposite direction upto a predetermined pressure. This predetermined cracking pressure can be adjusted within its maximum specified range.

Counter balance valves are seat type valves. They offer free-flow from their port B to A and give leak free closure in opposite direction upto a predetermined pressure. This predetermined cracking pressure can be adjusted within its maximum specified range.

A lever operated rotary type directional control valve is generally used for high pressure applications at low flow. These valves are used where leak-free closure is required.

A lever operated rotary type directional control valve is generally used for high pressure applications at low flow. These valves are used where leak-free closure is required.

Completely encapsulated control mechanism for protection against dirt. Five chamber design. Wide variety of spools available both in subplate and threaded model

Pilot operated directional control valves are hydraulically operated spool valves. They control the start, stop & direction of fluid flow. Available in 19 spool configurations. Available as spring centered and spring offset. Mounts on standard ISO 4401, IS10187.

Designed for single acting cylinders which are supposed to hold pressure. Ensures smooth decompression prior to return of the cylinder ram. Large return oil passage to reduce pressure drops, allowing rams to return under low external forces. Valves can be connected in series for independent multiple single acting cylinder operations.

Designed for single acting cylinders which are supposed to hold pressure. Specially suitable for rubber moulding presses. Ensure smooth decompression prior to return of the cylinder ram. Available as standard & Quick Exhaust. Large return oil passages allows rams to return under low external forces. Valves with quick exhaust feature have 2.34 times larger return passages. Provided with manual opening in case of power failures. Valves can be connected in series for independent multiple single acting cylinder operations. The valve is actuated by a solenoid controlled pilot.

Designed for single acting cylinders which are supposed to hold pressure. Specially suitable for rubber moulding presses. Ensure smooth decompression prior to return of the cylinder ram. Available as standard & Quick Exhaust. Large return oil passages allows rams to return under low external forces. Valves with quick exhaust feature have 2.34 times larger return passages. Provided with manual opening in case of power failures. Valves can be connected in series for independent multiple single acting cylinder operations. The valve is actuated by a solenoid controlled pilot.

4-port, spool type, solenoid operated, directional control valves with wet armature AC or DC coils and wide variety of spool types with spring centered and spring-offset arrangements.
Five chamber body and spool design to facilitate high flow.
Conforms to ISO4401-5, NFPA T3.5.1M R1 and ANSI B93-7 D 05 interface.
Available in 52 standard, interchangeable spool configurations.
Removable wet-armature AC and DC solenoids for quick replacement and conversions. Moulded solenoid coils to protect against moisture and ingress of dust. Individual solenoid plug-in connectors with indicator lights to ISO 4400 and DIN 43650.
Special R-rings for high extrusion resistance. Increased stability under high dynamic condition.
Override for operation of valve without electrical power.
Note on solenoid identification : Solenoid "a" is close to Port "A" and Solenoid "b" is close to Port "B" for a direct operated valve.

Completely encapsulated mechanism for protection against dirt. Five chamber design for better reduction in dynamic forces and longer valve life. Available as spring centered, spring off-set or detented model. Operating head can be rotated by 90° x 4 around spool axis for flexibility in mounting. Valve mounting interface conforms to ISO 4401-03-02. Five chamber body and spool design provides low-pressure drop, with maximum performance. Balanced spool design ensures proper shifting force for maximum reliability and long life. All spools and bodies are interchangable, simplifying maintenance.

4-port, spool type, directional control valves with hand lever actuation and wide variety of spool types with spring-centered, spring-offset and detent arrangements.

Pilot operated directional control valves are hydraulically operated spool valves. They control the start, stop & direction of fluid flow. Available in 19 spool configurations. Available as spring centered and spring offset. Mounts on standard ISO 4401, IS10187.

Available as spring centered, spring offset Valve mounting interface conforms to International and National standards. Minimum pilot pressure is 5 bar.

Pressure compensated. Check valve option for reverse-free flow. Four rotations of hand knob to facilitate the setting with ease. Thumb screw provision to retain valve setting. Stroke limiter available as an option.

Flow divider valves provide dual flow from a single source at a predetermined ratio, regardless of load. Maximum dividing error is 5%, Threaded port body.

Double throttle cum check, non pressure compensated, modular construction. Can be used as Metering-in or Metering-out device.

Double throttle cum check, non pressure compensated, modular construction. Can be used as Metering-in or Metering-out device.

Double throttle cum check, 2TCL10 are meant for controlling flow in one direction in circuit by simple throttling of flow. Reverse flow is free and is independent of throttle condition in opposite direction in same path.

These seat type valves allow free flow from port A to port B and give leak-proof closure in opposite direction. Available as inline mounting or Sub-plate mounting as per factory & ISO standards.

Seat type valves. Allow free flow from port A to port Band offer leakage free closure in opposite direction. Available in four sizes of standard interfaces conforming to
ISO 5781
IS 10187
DIN 24340
Each model available with options of four cracking pressures : 0.5, 1.5, 3 and 5 bar.

Seat type valves, Model CI with internal drain. Threaded or Sub-plate mounting construction. Available with two pilot piston size options only for Model CI.

Seat type valves, Model CI with internal drain. Threaded or Sub-plate mounting construction. Available with two pilot piston size.

Seat type valves, CL with external drain. Threaded or Sub-plate mounting construction.

These valves are available with the pilot operated check valve facility on either A or B or both A and B threaded ports.
The hydraulic opening operation for free flow in reverse direction is achieved by means of internal pilot pressure available from the other working port.

Seat type modular valve. Intended for by - passing. Pressure control valve,Pressure reducing valve etc. to achieve reverse free flow condition.Allow free flow from port A to port B or from port B to port A ( see model code ) and offer leakage free closure in opposite direction. Available in four sizes of standard interfaces conforming to ISO 5781, DIN 24340 or IS 10187 Each model available with options of four cracking pressures : 0.5, 1.5, 3 and 5 bar.

These modular valves are available with the pilot operated check valve facility on either 'A' or 'B' ports. The hydraulic opening operation for free flow in reverse direction is achieved by means of internal pilot pressure available from the other working port. Interface conforming to
ISO 4401-AB-03-04-A
IS 10187
DIN 24340
To ensure proper closure of both valve poppets, both user connections should be unloaded when the control valve is in the neutral by connecting with the return line.

These modular valves are available with the pilot operated check valve facility on either A or B or both A and B ports. The hydraulic opening operation for free flow in reverse direction is achieved by means of internal pilot pressure available from the other working port.
To ensure proper closure of both valve poppets, both user connections should be unloaded when the control valve is in the neutral position by connecting with the return line.

Seat type construction. Automatically connects it's P port to either A or B depending upon whichever of the two ports is at higher pressure level. Isolates port A and B from each other. Port P gets connected to tank, only if, port A and port B are connected to tank. Available both in Threaded and Sub-plate type.

Intended for prefilling and exhausting of large hydraulic cylinders. Can be used as anticavitation check valves. Decompression feature is optional up to size 80.

The Prefill Exhaust Valve (PV) is a hydraulic-pilot operated check valve with seat type construction. It allows free flow from port A to port B. Flow from port B to port A can be enabled by applying pilot pressure to it's port X.
The decompression feature enables the valve to open in two stages progressively, allowing smooth and rapid exhaust of the compressed oil. Opening and closing time of the valve can be influenced by providing Throttle-Check Valves in the X port line.
Flanged port A of the valve housing can be rotated around vertical axis through 360° to facilitate access to flange fixing bolts and flange orientation

These valves are suitable for mounting in manifold cavities machined as per ISO 7368. By selecting suitable cartridge and cover, it is possible to achieve functions like Check valve, Directional control valve, Unloading valve, Throttle valve etc. These valves offer fast response, have very low internal leakage and can handle very large flow rates. The cartridges are available with two area ratios.

Slip in cartridge valves are two port valves that can be inserted into compact manifold control blocks, having cavities that are machined as per ISO 7368. The function of the cartridge valve depends on the type of control cover used. With the help of suitable control cover the cartridge valve can assume pressure, directional, throttling or combination of these function.
Cartridge valves are available in two area ratios and four cracking pressures. Depending upon the function required, cartridge valve having Suitable area ratio must be used.
The control covers will have to be ordered separately.

4JP 06 Joystick Controlled Pilot Oil Unit is a Manual Joystick control valve, meant for providing variable pilot pressure to the hydraulic components like Proportional Pilot Operated Directional Control Valves, Pumps and motors etc., which need variable pilot pressure to control their outputs. The valve has two pairs of outlets, which can be operated independently or in tandem. Depending upon the Joystick tilt, the valve provides variable pressure to one or two of its outlets at a time. The pilot pressure can be regulated in the pressure range of 6 to 19 bar.

Pilot oil unit series 4JP are intended for giving sensitive pressure signals to pumps, Valves or Hydraulic motors which need to be controlled by remote pilot pressure. Functioning of these valves is based on spool type direct acting pressure reducing valve principle.

Currently we are supplying this valve to
L&T John Deere for Tractors
Telcon for Tata - John Deere Back Hoe Loaders.

Lock valve, basically two position directional control valve designed to have flexibility in diverting the flow. The valve is provided with single pump connection, three common ports designated as 'A' and four common tank ports designated as 'T'. In normal position, pump flow is connected to A ports and at an angle in between 78° - 100° port A is connected to tank with throttling effect. Currently we are supplying this valve to
Telcon for Tata - Hitachi Excavators.

Currently we are supplying this valve to
Telcon for Tata - John Deere Back Hoe Loaders.

Currently we are supplying this valve to
Hyva Hyderabad.

Currently we are supplying this valve to
Telcon

Currently we are supplying this valve to
Telcon

Designed specially for multistation directional control valves, CETOP- 4.2 - A - 05(P). Number of stations vary from minimum 2 to maximum 7.

Designed specially for multistation directional control valves, CETOP- RP 35 H size 3.

Number of stations vary from minimum 2 to maximum 10.

Non adjustable differential type. Spring loaded sealed piston construction. Encapsulated design for protection against dust. Six pressure ranges available, which can be adjustable upto 10, 50, 100, 200, 350 and 420 bar. Transparent plug-in connector is available with LED

Threaded type and Sub-plate mounting style. Paper element as filtration media. Spin-on disposable canisters. Integral by-pass check valve.

These valves are recommended , when the pumps are installed with negative suction head. Threads for the Foot valve are sized to provide approximately 3 times larger capacity of the strainer. Strainer is not included in the scope of supply.